Search results for "Accuracy and precision"
showing 10 items of 58 documents
A comparative study on sample preparation procedures for supplementary foods by ICP-OES: Green chemistry considerations
2015
An inductively coupled plasma optical emission (ICP-OES) method was developed for the simultaneous determination of major, minor and trace elements in food. Preliminary studies focused on selecting suitable operational conditions in order to provide the highest sensitivity and to maximize the number of analytes to be determined without spectral or matrix interference. Ruthenium and rhenium were evaluated as internal standards and samples were analyzed at different dilution levels. Furthermore, a comparative study was carried out by using three sample digestion methods, microwave-assisted digestion with HNO3/H2O2, dry ashing and dry ashing with Mg(NO3)2/MgO as an ashing aid. Adequate precisi…
Ultrasound-assisted sequential extraction method for the evaluation of mobility of toxic elements in contaminated soils
2005
A method for the fast sequential extraction of toxic elements in contaminated soil samples using an ultrasonic water bath, followed by determination with inductively coupled plasma optical emission spectrometry (ICP-OES), was developed and compared with other methods introduced in the literature. The five-step sequential extraction (Tessier scheme) was shortened using ultrasound-assisted sequential extraction (UASE). The optimization of the five-step sequential extraction was based on the analysis of SRM 2710 using Tessiers’s method as a reference. Several extracting solutions with different sonication times and temperatures were tested in the optimization procedure. Concentrations of arsen…
Addition of thiourea and hydrochloric acid: Accurate nanogram level analysis of mercury in humic-rich natural waters by inductively coupled plasma ma…
2020
Abstract An analytical method was developed for the direct determination of total mercury in natural waters at low ng L−1 level by inductively coupled plasma mass spectrometry (ICP-MS). The presented method overcomes previously observed problems relating to poor spike recoveries by adding 0.12% thiourea in addition to 3% HCl to all samples and standards. The sample preparation is fast and easy to perform by the developed method since it requires only the addition of HCl and thiourea to the water samples. A very low instrument detection limit (0.4 ng L−1) was obtained without time-consuming preconcentration procedures. The accuracy and precision of the developed method were found excellent b…
Copper, iron and zinc determinations in human milk using FAAS with microwave digestion
2000
Abstract A method for determining copper, iron and zinc in human milk was optimized and validated. It includes microwave mineralization of the sample and measuring the elements by flame atomic absorption spectroscopy (FAAS). Only 2 ml of milk is needed, and the method is free of matrix interferences. The values obtained for the detection limits (0.07; 0.07; 0.11 μg/ml milk, for copper, iron and zinc) precision of the method, intra-assay (2.9; 5.2; 6.1%RSD for copper, iron and zinc) and accuracy, evaluated using recovery assays (98.8; 100.4; 95.9% for copper, iron and zinc) show that the method is useful for the purpose mentioned. Moreover, the method is rapid and simple, and the determinati…
Determination of knee joint cartilage thickness using three-dimensional magnetic resonance chondro-crassometry (3D MR-CCM)
1996
The objective of this article was to analyze the accuracy and precision with which the quantitative distribution of articular cartilage can be determined in the knee joint using MRI. A three-dimensional (3D) technique that accounts for the out-of-plane deviation of the interface normal in strongly curved joint surfaces (3D MR-CCM) has been developed for cartilage thickness measurements. Eight cadaveric knee-joint specimens and six volunteers were imaged using a fat-suppressed gradient-echo sequence at a resolution of 2 x 0.31 x 0.31 mm3. Cartilage volumes and topographical thickness maps were obtained and compared with those derived from anatomical sections by image analysis. The deviation …
Influence of image reconstruction parameters on cardiovascular risk reclassification by Computed Tomography Coronary Artery Calcium Score
2018
Objective: To investigate the influence of different CT reconstruction parameters on coronary artery calcium scoring (CACS) values and reclassification of predicted cardiovascular (CV) risk. Methods: CACS was evaluated in 113 patients undergoing ECG-gated 64-slice CT. Reference CACS protocol included standard kernel filter (B35f) with slice thickness/increment of 3/1.5 mm, and field-of-view (FOV) of 150â180 mm. Influence of different image reconstruction algorithms (reconstructed slice thickness/increment 2.0/1.0â1.5/0.8â3.0/2.0â3.0/3.0 mm; slice kernel B30f-B45f; FOV 200â250 mm) on Agatston score was assessed by Bland-Altman plots and concordance correlation coefficient (CCC) ana…
GEOV1: LAI, FAPAR essential climate variables and FCOVER global time series capitalizing over existing products. Part 2: Validation and intercomparis…
2013
International audience; This paper describes the scientific validation of the first version of global biophysical products (i.e., leaf area index, fraction of absorbed photosynthetically active radiation and fraction of vegetation cover), namely GEOV1, developed in the framework of the geoland-2/BioPar core mapping service at 1 km spatial resolution and 10-days temporal frequency. The strategy follows the recommendations of the CEOS/WGCV Land Product Validation for LAI global products validation. Several criteria of performance were evaluated, including continuity, spatial and temporal consistency, dynamic range of retrievals, statistical analysis per biome type, precision and accuracy. The…
Optical Characterization Method for Tilted or Decentered Intraocular Lenses
2016
Purpose To test and validate a method for measuring the optical quality and optical power of monofocal intraocular lenses (IOLs) in the presence of a tilt or a decentration as well as its optical power. Methods The experimental system consists of an artificial eye (wet-cell) and a commercial aberrometer with a Shack-Hartmann sensor. Optical image quality parameters such as point spread function (PSF), modulation transfer function (MTF), and the simulations of the retinal image of an extended object are computed from the in vitro wavefront data of an IOL. Repeatability and reproducibility of the system are tested. Mathematical and ray-tracing simulations are used to ascertain the precision a…
Comparison of UV and charged aerosol detection approach in pharmaceutical analysis of statins
2009
Abstract CAD (charged aerosol detector) has recently become a new alternative detection system in HPLC. This detection approach was applied in a new HPLC method for the determination of three of the major statins used in clinical treatment—simvastatin, lovastatin and atorvastatin. The method was optimized and the influence of individual parameters on CAD response and sensitivity was carefully studied. Chromatography was performed on a Zorbax Eclipse XDB C18 (4.6 mm × 75 mm, 3.5 μm), using acetonitrile and formic acid 0.1% as mobile phase. The detection was performed using both CAD (20 pA range) and DAD (diode array detector—238 nm) simultaneously connected in series. In terms of linearity, …
Range-based versus automated markerless image-based techniques for rock art documentation
2014
Nowadays there is a huge proliferation of fully automatic image-based solutions producing either three-dimensional (3D) point clouds or 3D models. However, the reliability of the output is not usually reported and clarified. This paper presents a comparison of the 3D modelling results achieved on two rock art shelters at separate archaeological sites using a high-resolution digital camera. The 3D point clouds were produced using automatic image-based photogrammetric and computer vision software running either locally (FOTOGIFLE and VisualSFM) or through a webbased reconstruction service (Autodesk 123D Catch). The first two automatic approaches are compared with a manual bundle block adjustm…